How does the water-meter test actually work?
Turn every fixture and water-using appliance off, including ice makers and irrigation, then read the meter and watch it. Any movement over a quiet half hour means water is leaving the pressurised system. A still meter rules a supply leak out and redirects the whole search.
This is the single most useful ten minutes in the whole process and it costs nothing. Most meters have a small low-flow indicator that turns with any flow at all, which is more sensitive than the main dial. Note the reading, wait, read it again; if the number has moved and nothing in the house was running, water is going somewhere it should not.
What it cannot tell you is where. It also will not catch a drain leak, a roof leak or ground water, because none of those involve the pressurised supply, which is exactly why the result is so useful: it halves the search in one step. If you want to do something before a technician arrives, do this and write down what you saw.
Does thermal imaging see water through a wall?
No. A thermal camera sees surface temperature, and wet material usually reads cooler because evaporation takes heat from it. That makes it excellent at showing the shape and extent of a damp area, but every finding has to be confirmed with a moisture meter before anyone cuts.
The reason to be careful about this is that thermal images are persuasive. A cool patch can be insulation that has slumped, a stud, a duct, or a draught, and treating every blue shape as a leak is how unnecessary holes get made. Used properly, the camera tells the technician where to put the meter, and the meter decides.
It works best where there is a temperature difference to begin with, which in a heated Everett house during the wet season is most of the time. A hot supply line under a slab can also show as a warm line, which is one of the few cases where the camera points almost directly at the problem. Even then, the reading comes before the saw.
Why is telling leaks apart from winter water so important here?
Because the three common sources need different trades and are treated differently on a claim. A plumbing leak, seepage from saturated ground and rain in through a storm-damaged roof can produce the same damp floor in a Snohomish County winter while needing three different repairs.
The insurance difference is real. The Washington Office of the Insurance Commissioner notes that typical homeowners policies generally do not cover flood, which needs a separate policy bought beforehand, while wind-driven rain through a storm-damaged roof or window is often covered. A sudden plumbing failure is a different clause again. A cause recorded wrongly at the start is hard to correct later, and the record a detection visit produces is written with that in mind.
The practical difference matters just as much. Opening a wall on the assumption of a burst pipe, when the water has been arriving through the slab joint every December, means repairing the wall and watching the same patch return. During the December 2025 atmospheric river more than fifteen inches of rain fell on the mountains in 72 hours, and in that kind of week a great many wet floors in this county had nothing to do with plumbing.
What affects the cost of finding a leak?
How much area has to be mapped, how many plausible sources there are, whether the suspected line is under a slab, and how accessible the wet area is. A single wet room with one candidate above it is quick. The price is explained and approved before any work starts.
Mapping a single room and confirming one source is a short visit. A house with damp showing in three places, a remodel history that moved the plumbing, a finished basement, or a suspected line under a slab takes longer, needs more instruments and sometimes a return visit in different weather to see whether the pattern tracks the rain.
Detection is also the step that saves money rather than costing it, because the alternative is exploratory demolition. Everett Water Damage Restoration publishes no figures, here or anywhere on the site, and a price quoted before anyone has seen the house would be a guess. You get a scope and a price explained and agreed first, and if the readings point at another trade you are told that rather than sold drying you do not need. The guide on water damage restoration cost in Everett explains what moves a quote across all of this work.
- How many rooms or surfaces have to be mapped
- How many plausible sources the layout allows
- Whether a line under a slab is suspected
- Access to the wet area, including cabinetry and finished basements
- Whether a second visit in wet weather is needed to confirm a pattern
What should I do before the technician arrives?
Run the meter test and note what you saw, photograph the damp area with a date, and write down when it started and whether it tracks rain or fixture use. Clear access to the wall or floor in question. Do not start cutting into anything.
The timeline is the most valuable thing you can hand over. When did it first appear, did anything change in the house just before, does it get worse in rain, after a shower, overnight, or at no particular time? Those four answers rule out more than any instrument does. A photograph each day with the date on it is better than a description from memory.
If you can hear water running in a wall and cannot account for it, shutting the main off at the street or the house valve is reasonable while you wait, and it also serves as a test: if the noise stops and the damp stops spreading, the water was coming from the supply. Beyond that, leave the wall closed. An opening made in the wrong place costs a repair and destroys the moisture pattern the technician was going to read.